Identify and Use Network Hand Tools

1. What is the nominal duration of the module "Identifying and Using Network Hand Tools"?

A. 20 Hours B. 22 Hours C. 25 Hours D. 30 Hours

2. Why are network hand tools considered essential?

A. For the physical installation, termination, and testing of network cabling and equipment. B. For configuring network software. C. For managing user accounts. D. For writing network documentation.

3. What is the primary function of a cable stripper?

A. To terminate a cable with a connector. B. To test for electrical continuity. C. To cut a cable to length. D. To remove the outer jacket or insulation from a network cable.

4. Which tool is used to terminate a cable with a connector?

A. A cable stripper B. A crimper C. A punch-down tool D. A continuity tester

5. What is the purpose of a punch-down tool?

A. To terminate network cables onto a patch panel or keystone jack. B. To crimp RJ45 connectors. C. To strip the outer jacket of a cable. D. To test the integrity of a fiber optic cable.

6. Which tool is used to check for an electrical connection in a network cable?

A. A crimper B. A wire cutter C. A continuity tester D. A loopback plug

7. What is the function of a wire cutter or side cutter?

A. To punch down cables. B. To strip the outer jacket. C. To test for connectivity. D. To trim and cut network cables to the desired length.

8. Which connector is the standard for terminating Ethernet network cables?

A. RJ45 B. RJ11 C. Coaxial D. USB

9. What tool is used to locate and identify a specific cable in a bundle of wires?

A. A continuity tester B. A cable toner and probe kit C. A crimper D. A multimeter

10. What is the function of a cable tester?

A. To terminate a cable. B. To strip a cable. C. To verify that a network cable is properly wired and free of faults. D. To cut a cable to length.

11. What do the 568A and 568B standards refer to?

A. Wiring color codes for terminating Ethernet cables. B. Types of network hand tools. C. Network security protocols. D. Network performance metrics.

12. What tool is used to send a signal through a cable to help trace its path?

A. A crimper B. A punch-down tool C. A cable tester D. A tone generator

13. What is a crucial safety precaution when using network hand tools?

A. Using a tool for a purpose other than its design. B. Wearing safety glasses and using tools for their intended purpose. C. Not wearing any protective gear. D. Working in a dimly lit area.

14. What is a modular crimper?

A. A crimper that can only be used for RJ45 connectors. B. A crimper that is powered by electricity. C. A crimper that can be used to crimp multiple types of modular connectors. D. A crimper used for coaxial cables only.

15. What are keystone jacks used for?

A. To provide a modular connection point for network cables in a wall plate or patch panel. B. To cut cables to a precise length. C. To test the speed of a network connection. D. To tighten cable ties.

16. What is the purpose of a multimeter?

A. To test the integrity of a fiber optic cable. B. To send a signal through a cable. C. To crimp network connectors. D. To measure electrical properties such as voltage, current, and resistance.

17. What is a loopback plug used for?

A. To check for continuity in a cable. B. To test network interface cards (NICs) by redirecting a signal back to the sender. C. To locate a specific cable in a bundle. D. To crimp a connector onto a cable.

18. What is the function of a cable tie gun?

A. To cut network cables. B. To install a patch panel. C. To tighten and cut cable ties, organizing and securing cables. D. To test the speed of a network.

19. How are Ethernet cables categorized?

A. Based on their data transfer rate and frequency, such as Cat5e, Cat6, and Cat6a. B. Based on their color and length. C. Based on their manufacturer. D. Based on their weight and material.

20. What is a protocol analyzer used for?

A. To check the voltage of a cable. B. To capture and analyze data packets on a network. C. To crimp RJ45 connectors. D. To terminate fiber optic cables.

21. Which tool is used to measure the power of fiber optic signals?

A. A multimeter B. A continuity tester C. An optical power meter (OPM) D. An optical time-domain reflectometer (OTDR)

22. What is an OTDR used for?

A. To test the integrity of fiber optic cables and locate faults. B. To measure the power of fiber optic signals. C. To cut fiber optic cables. D. To splice fiber optic cables.

23. What is the first step in terminating an Ethernet cable?

A. Crimping the connector. B. Tracing the wires. C. Putting on the connector. D. Stripping the outer jacket of the cable.

24. What is important to ensure when using a punch-down tool?

A. That the tool is brand new. B. That the wires are in the correct order to match the wiring standard. C. That the punch-down tool is very expensive. D. That all cables are the same color.

25. What is a patch panel?

A. A board with multiple network ports used to organize and manage network cables. B. A type of network tool. C. A piece of software used to manage a network. D. A type of network cable.

HNS Exam: Identifying and Using Network Hand Tools

Exam Results